how to flash a ledger board against brick wall

How to attach a ledger to a brick wall

Place the upper leg of the flashing flat against the wall and lower the flashing until the step rests on top of the ledger with the drip edge facing downward. Attach the flashing to the brick wall with masonry nails hammered in and spaced every 30 cm (12 inches) across the length of the flashing.【Get Price】

Ledger Board Attachment to Brick Siding | Decks.com by

You should never attach a deck to a brick wall. In other than very old homes, exterior brick walls are only a single wythe (layer) of brick veneer. Brick veneer is not designed or allowed by building codes to support anything other than the weight of the bricks above. Videos 09:10 DIY Deck (Part 3): How to install code approved ROT FREE Ledger Board brick veneer without flashing? YouTube 2019-03-22T19:57:26Z04:22 How to Install the BVLZ Brick Veneer Ledger Connector YouTube 2019-08-28T18:37:42Z08:46 Ledger board installations, where and why on a stucco wall YouTube 2012-06-25T18:38:59Z07:05 How to build a deck: Attaching the ledger board YouTube 2018-08-24T18:58:24Z06:49 08 Installing Over Flashing YouTube 2017-07-31T18:02:24Z12:31 How to Install and Flash a Deck Ledger, Start to Finish YouTube 2019-05-30T19:35:42Z07:09 How why and where to install a ledger board on a stucco wall with same day scratch and brown coat YouTube 2011-11-14T01:36:00Z02:04 How to Attach a Ledger Board for a Deck YouTube 2015-05-26T15:00:00Z03:45 How to install a ledger board on existing stucco wall YouTube 2018-05-15T03:27:18Z10:16 BR Brick Bracket Installation Video YouTube 2016-01-22T02:49:42Z More results in videos【Get Price】

Brick Flashing | Ledger Flashing | Install Flashing

Mark a line for the ledger board. Step 2 Find a grout line that is approximately 2 inches or more above the ledger board line. This line ensures your flashing will be above the actual porch floor or deck flooring material.【Get Price】

Deck Ledger on Brick...Flashing Needed? - Fine Homebuilding

attaching a ledger board to a brick wall Depends on what the brick is attached to. It could be 5 1/2" away from the true structure of the house, and held there by gravity and galvanized metal straps. Can be done, just may not be the "normal" way of doing things ...【Get Price】

Flashing A Deck Ledger Board Properly - How To

Snap a line on the Tyvek at the height of the top edge of your ledger board. Cut the Tyvek on that line and remove it from that line below. Temporarily lift up the Tyvek enough that you can get an inch or two of the self adhesive flashing BEHIND it. Install the self【Get Price】

Attaching a Deck Ledger to a Home Through Brick or Masonry Veneer — the BVLZ Solution - Simpson Strong-Tie Structural Engineering Blog

Brick or masonry veneer has traditionally posed a problem to homeowners and contractors seeking to attach a deck to a home without removing large portions of the veneer or siding. No longer is that the case, thanks to the innovative BVLZ brick veneer ledger connector from Simpson Strong-Tie. In this post, Rachel Holland, P.E., an … Continue reading "Attaching a Deck Ledger to a Home Through ...【Get Price】

flashing decks to brick wall - JLC-Online Forums

Otherwise, One way to flash it is to terminate the brick above the deck on a steel lintel and flash it out over the deck. This flashing would be installed against the sheathing (above the steel angle) and under the felt paper.【Get Price】

Wall Flashing Techniques For Leakproof Walls

Membrane flashing was retrofitted here to protect the ledger and wall framing from water intrusion. For water protection here, at a minimum install a cap flashing that tucks under the sheathing wrap and goes over the ledger.【Get Price】

How to Anchor a Deck to Brick Veneer - YouTube

Want your new deck to last twice as long as others? Going crazy keeping your current deck stained? This video is part of my ebook Love Your Deck. Check it ...【Get Price】

Brick Flashing | Ledger Flashing | Install Flashing

Brick Flashing Basic Tips Step 1 Mark a line for the ledger board. Step 2 Find a grout line that is approximately 2 inches or more above the ledger board line. This line ensures your flashing will be above the actual porch floor or deck flooring material. Step 【Get Price】

3

flashing deck ledger to brick veneer - Fine Homebuilding

I believe your best bet would be to put 1" pipe spacers between the ledger and the wall and not flash at all in this case. It's tricky but you pre-drill your ledger, feed your 5" lag bolt through the ledger, through the spacer and into the sill of the house.【Get Price】

Attaching a Deck Ledger to a Home Through Brick or Masonry Veneer — the BVLZ Solution - Simpson Strong-Tie Structural Engineering Blog

By orienting the screws at an upward angle, we were able to impose a tension force at the top of the rim, and then the compression strut stops the ledger from bearing in on the brick. These two components act in a truss-like manner.【Get Price】

flashing decks to brick wall - JLC-Online Forums

Otherwise, One way to flash it is to terminate the brick above the deck on a steel lintel and flash it out over the deck. This flashing would be installed against the sheathing (above the steel angle) and under the felt paper.【Get Price】

What is the proper way to flash a deck ledger? - GreenBuildingAdvisor

Spacing the ledger off the wall minimizes moisture damage because water can flow freely between the ledger and the wall flashing. The code permits a 1⁄2-in. stack of washers as a spacer, or you can use alternatives such as Deck-2-Wall Spacers (www.deck2wallspacer.com).【Get Price】

How to Attach a Ledger to a Cinder Block Wall | eHow

Set your ledger board on a sturdy level surface. Use a ¼-inch wood bit to drill pilot holes for the fasteners. Put one hole centered 2 to 3 inches from each end and at least one hole in the center of the board. Drill more holes depending on the length and width of the ledger.【Get Price】

How to Use Flashing Between Brick & Siding | Home Guides | SF Gate

Install the flashing before you finish the top of the brick wall, as the flashing must go behind the siding as well as behind and under the top row of bricks that angle outward to cover the top...【Get Price】

Installing Deck Ledgers | DIY Deck Plans

To attach a ledger against a wall through brick veneer: Mark anchor locations on your ledger and drill through the board with a ½” bit Position the ledger against the wall and mark the anchor positions through the hole onto the wall.【Get Price】

Five Ledger Board Techniques | Detailed Diagrams

The lags should pass through by at least 1/2" on the back side of the band board. Note: The deck boards have been depicted with a gap between the first board and the house only to emphasize flashing overlapping the ledger. On site the first board would be positioned within 1/2" from the wall flashing. 1/2" carriage or cap bolts【Get Price】

How to Attach a Ledger Board to a Masonry Wall | DoItYourself.com

Using a 3/8 masonry bit in the hammer drill, drill the holes through the wall in the places that you marked. The holes need to be at least three inches deep into the wall. Insert the expansion anchors into these holes so that they are flush with the wall. Step 5 – Attach the Ledger Board to the Wall.【Get Price】

What is the proper way to flash a deck ledger? - GreenBuildingAdvisor

Spacing the ledger off the wall minimizes moisture damage because water can flow freely between the ledger and the wall flashing. The code permits a 1⁄2-in. stack of washers as a spacer, or you can use alternatives such as Deck-2-Wall Spacers (www.deck2wallspacer.com).【Get Price】

How to Attach a Deck to a Brick Sill | Home Guides | SF Gate

Position the ledger flat against the face of the wall, and align the upper edge at the chalk line on the flashing. Align the ends with the ends of the flashing. Use the drilled holes in the ledger...【Get Price】

How to Attach a Ledger to a Cinder Block Wall | eHow

Set your ledger board on a sturdy level surface. Use a ¼-inch wood bit to drill pilot holes for the fasteners. Put one hole centered 2 to 3 inches from each end and at least one hole in the center of the board. Drill more holes depending on the length and width of the ledger.【Get Price】

Ledger installation on brick - DoItYourself.com Community Forums

If you use lead anchors, or build it free-standing against the brick wall, I see no reason to seal or flash the ledger board and bolts, as long as the brick facade is not penetrated. The washers between the ledger board and brick wall seem like a good idea to allow drainage, if using anchors.【Get Price】

How to Use Flashing Between Brick & Siding | Home Guides | SF Gate

Install the flashing before you finish the top of the brick wall, as the flashing must go behind the siding as well as behind and under the top row of bricks that angle outward to cover the top...【Get Price】

Deck Ledger Board Flashing - The Critical Concern

Once the ledger board flashing is in place behind the siding you can install the ledger board underneath. Afterwards you can use a wood block and a hammer to bend the flashing over the ledger board to form the drip edge.【Get Price】

Five Ledger Board Techniques | Detailed Diagrams

The lags should pass through by at least 1/2" on the back side of the band board. Note: The deck boards have been depicted with a gap between the first board and the house only to emphasize flashing overlapping the ledger. On site the first board would be positioned within 1/2" from the wall flashing. 1/2" carriage or cap bolts【Get Price】

Wall Flashing Techniques For Leakproof Walls

Where a slope roof meets a sidewall, slip the upper legs of the step flashing under the sheathing wrap (see Illustration). CLICK TO ENLARGE Make sure the sheathing wrap overlaps all step flashings. Where snow buildup is likely, add a wide band of peel-and-stick membrane lapped over the step flashing, but under the sheathing wrap.【Get Price】

Ledger Flashing | Brick Flashing | Install Flashing

See our ledger board installation details in our porch foundation section. Ledger Flashing - Brick See our information about brick flashing. The process is basically the same but there is an added important step. Flashing installed over ledger board on brick【Get Price】

What is the proper way to flash a deck ledger? - GreenBuildingAdvisor

Spacing the ledger off the wall minimizes moisture damage because water can flow freely between the ledger and the wall flashing. The code permits a 1⁄2-in. stack of washers as a spacer, or you can use alternatives such as Deck-2-Wall Spacers (www.deck2wallspacer.com).【Get Price】

Q&A: Bolting a Ledger to Brick Veneer | JLC Online

Q. What’s the best way to attach a deck ledger board to a wood-framed house with brick veneer? A.Christopher DeBlois, P.E., an engineer with Palmer Engineering in Chamblee, Ga., responds: Whenever there is a design alternative, I generally recommend against bolting a deck ledger board to brick veneer. ...【Get Price】

Putting ledger board against uneven brick wall, what are my options? : HomeImprovement

Went to put ledger board, about 5 1/2' long, against house, and a few bricks stick out in the middle preventing the board from laying flat. What are my options? Can I grind the brick down? Can I shim between the brick and the ledger board? Thanks for any information!【Get Price】

Ledger installation on brick - DoItYourself.com Community Forums

If you use lead anchors, or build it free-standing against the brick wall, I see no reason to seal or flash the ledger board and bolts, as long as the brick facade is not penetrated. The washers between the ledger board and brick wall seem like a good idea to allow drainage, if using anchors.【Get Price】

Deck Ledger Board Flashing - The Critical Concern

Once the ledger board flashing is in place behind the siding you can install the ledger board underneath. Afterwards you can use a wood block and a hammer to bend the flashing over the ledger board to form the drip edge.【Get Price】

Deck ledger attachment on brick veneer wall. | The Building Code Forum

a ledger board to be tightened against the brick veneer will then push the brick veneer inwards, ... Have an engineer design attaching a 8" angle iron ledger by bolting it to the header, lay the brick veneer wall and 3"+ angle iron ledger should be ...【Get Price】

Porch & Deck Ledger Flashing to buildings - Construction Details to Avoid Leaks & Rot - Best Practices Guide

Porch & Deck Ledger Flashing to buildings - Construction Details to Avoid Leaks & Rot Steve Bliss's Building Advisor at buildingadvisor.com helps homeowners & contractors plan & complete successful building & remodeling projects: buying land, site work, building design, cost estimating, materials & components, & project management through complete construction.【Get Price】

How to Replace a Rotted Ledger Board or Sill Plate | eHow

Expose the ledger board of your building by removing any siding covering the bottom of the wall where the wood meets the foundation. Pry wooden siding away with a flat pry bar, taking care not to damage the siding. Chip away brick or stucco using a hammer【Get Price】

Product Details